Epoxy Floor Repair in Orlando — Recoat, Resurface & Stop the Peeling for Good
Hot-tire pickup in the garage. A topcoat that lifted before the first summer was out. A back-of-house floor that can't afford to close. Central Florida's heat, afternoon storms, and high water table punish coatings that weren't prepped for them — and a quick recoat over the failure just buys a few more months. The team finds why your floor let go, then resurfaces it so it stays down. Free assessments across Orange, Seminole, Osceola, and Lake counties.
Why Orlando Floors Fail — and What Actually Fixes Them
Most epoxy in Central Florida doesn't fail because the resin was cheap. It fails because of where it was poured. Orlando sits on sandy, fast-draining soil over a shallow water table and the Floridan aquifer, and almost every home and shop here is built slab-on-grade — concrete sitting inches above damp ground, with no crawl space or basement to act as a buffer. Ground moisture rises through that slab as vapor day after day. When a coating goes down without that vapor drive being measured and managed first, the moisture pushes back until the epoxy lifts, blisters, or sheets off.
Then there's the climate stacked on top of it. Long, hot summers and the daily afternoon thunderstorm cycle keep humidity high and swing the temperature of an un-airconditioned garage slab by twenty-plus degrees in an afternoon. That movement is brutal on a bond that was already weak — and it's why so many Orlando garages show hot-tire pickup, where summer-soft tires pull the topcoat right off the floor in patches.
Recoating over that without fixing the cause is the trap most floors fall into. The team starts the other way around: read the slab, identify whether it's vapor drive, a contaminated or under-profiled surface, or a coating that was never rated for this environment — and only then choose how to resurface it. The goal is a floor that holds through the next August, not one that looks new until the rainy season.
Read why epoxy floors fail in Orlando →
We repair, resurface, and maintain floors across Greater Orlando — from the resort and hospitality corridor down through Kissimmee to the fast-growing suburbs of Winter Park, Lake Mary, Sanford, and Ocoee.
What We Fix — and How We Make It Last
Repair, recoat, or full resurface: the right answer depends on the slab. Here's what the team handles for Central Florida floors.
Hot tire
Hot-Tire & Peeling Repair
The most common call we get from Orlando garages: lifted patches where summer-hot tires peeled the topcoat. We re-profile those zones and lay back a film that won't soften and release in July.
Why Orlando floors fail →Vapor
Slab Vapor Mitigation
On the wet slab-on-grade pours common across Central Florida, we read the vapor drive and install a moisture-block primer before resurfacing — so ground moisture can't push the new coat off the way it pushed off the last one.
Resurface
Strip-Down & Resurface
When the old film is delaminated past saving, we diamond-grind it back to clean concrete, correct the slab, and rebuild the system from the primer up — spec'd for Orlando heat and humidity, not a generic kit.
Open
Repairs That Stay Open for Business
Resort kitchens, restaurant lines, and showroom floors can't shut down. We zone the work, cure around your hours, and patch high-traffic wear, chips, and cracks without closing the room — built for the hospitality crowd that never really sleeps.
Topcoat
Re-Topcoat & Maintenance Plans
A healthy floor doesn't need a teardown — it needs a fresh wear coat before the UV and traffic reach the base. We schedule re-topcoats and check-ins around your floor's traffic so you catch wear early and never go back to bare resin.
Honest call
Resurface, Don't Replace
Restoring a slab almost always beats tearing it out — especially on the 2000s-era tract-home garages and flip-house floors all over Orlando's growth ring. If a spot fix is all you need, that's what we'll tell you.
See full pricing guide →Our Orlando Repair Process
Read the slab first, fix the cause, then resurface — scheduled around Central Florida's heat and rain so the new coat actually cures.
Free Assessment
~45 minWe come to your Orlando property, walk the failure with you, and document what's lifting, blistering, or hot-tire-peeled and how far it's spread. No cost, no obligation. Schedule yours free.
Diagnosis & Testing
1–2 hrsWe run calcium-chloride and RH slab-moisture tests, adhesion pulls, and a look at the failed material — sorting a wet slab-on-grade pour from a contaminated surface from a coating that was simply never rated for Florida.
Surface Preparation
2–4 hrsBased on what the slab told us, we either scarify and recoat or diamond-grind the old film off to bare concrete. If the vapor reading calls for it, the moisture-block primer goes down at this stage — before anything else.
Repair & Re-Coat
3–5 hrsWe fill cracks, patch the damaged zones, and lay back the coating system matched to your slab — chemistry and topcoat chosen for the heat, humidity, and traffic this particular floor actually sees.
Cure & Warranty
24–72 hrsWe time the cure around Orlando's heat and the afternoon storm window so the coating sets right, then hand you a written warranty in plain language — no fine-print disappearing acts.
Floor Acting Up? Step 1 Is Free.
Book a no-obligation slab read and we'll tell you whether it's a spot fix, a recoat, or a full resurface.
Orlando Repair & Resurface Projects
Before-and-after results from peeling, hot-tire, and worn floors brought back across the Orlando area.
Rated 4.8★ on Google — Orlando Reviews
Real reviews from real Orlando homeowners — verified on Google.
"We had Epoxy Orlando redo our garage floor this summer and it totally changed the space. The installers were on time, polite, and really knew their stuff. I picked a metallic finish and it looks amazing when the light hits it. No peeling or dull spots even after all the rain and humidity. Would absolutely use them again."
"Got my garage done last month. The epoxy came out perfect and the color chips hide dirt really well. Team finished quicker than expected."
"Great job from start to finish. Crew was fast, clean, and super respectful of the property. My shop floor looks incredible."
Epoxy Repair FAQs — Orlando
Common questions about epoxy floor repair and maintenance in Orlando.
Florida's extreme humidity and moisture vapor transmission (MVT) through concrete slabs are the number one cause of epoxy failure in Orlando. When installers skip proper moisture testing or use coatings incompatible with high-moisture environments, the bond between epoxy and concrete weakens. Moisture trapped beneath the coating creates hydrostatic pressure that causes peeling, bubbling, and delamination.
Post-flood slabs and older homes without modern vapor barriers are especially vulnerable. Ascent Epoxy tests every slab for moisture before recommending a repair strategy.
It depends on the condition of the existing coating and the underlying concrete. In some cases, we can scarify the surface and apply a new system directly over the old one. However, if the previous coating is severely delaminated, contaminated, or applied over untreated moisture issues, a full strip-down to bare concrete is necessary for a lasting repair.
We perform on-site testing to determine the right approach for your specific floor — no guesswork.
Costs vary depending on the scope of damage, square footage, whether a full strip is needed, and if moisture mitigation is required. Spot repairs start significantly lower than full re-coats. In many cases, repair is a fraction of the cost of a complete new installation.
We provide free on-site assessments with transparent pricing so you know exactly what to expect before any work begins. See our Orlando pricing guide for general ranges.
Yes. Many Orlando slabs affected by Hurricane Ian or Milton have chronic moisture issues that cause coatings to fail repeatedly. We specialize in post-flood slab preparation, including calcium chloride moisture testing, moisture mitigation systems, and coatings specifically engineered for high-MVT environments.
Our process addresses the root cause so your new coating bonds permanently instead of peeling again within months.
Yes. We offer ongoing maintenance plans that include periodic inspections, cleaning guidance, minor touch-ups, and re-coating schedules tailored to your floor's traffic level and environment. Maintenance plans help extend the life of your epoxy floor by years and catch small issues before they become costly repairs.
Contact us for a customized maintenance plan for your home or business.
Design your epoxy floor in 60 seconds.
Pick your size, finish, and color. See a real preview and your Orlando price range before you call.
Open Floor Studio →